This rattle could possible be a nut from the loop connector that has come loose and fallen off. if it is inside the metal box you should be able to take the battery and jiggle the box and see what...
Type: Posts; User: rcsnake
This rattle could possible be a nut from the loop connector that has come loose and fallen off. if it is inside the metal box you should be able to take the battery and jiggle the box and see what...
If you are hunting for targets that may wrap around the corner so to speak it make be worth while to make sure that all the VDI's in that area including +95, through -93 is accepted. As pointed out...
Best of luck with it Lockman..... Just take time to learn the machine.
Bob
Ground balancing over a target will pull the ground balance point if the target strength and phase reading from target combined with the phase and target strength from the ground signal still falls...
To tell if the instrument is properly ground balance can be accomplished by raising the loop to waist level and then pulling the trigger to put the instrument into the pinpoint mode. Then lower the...
I am not Jack but might be able to answer your question. Raising or lowering the Disc sensitivity will not change what a target will VDI at. What this will do when hunting in the all metal mode the...
The polar plot is very useful for bottle-caps that are shallow (5 to 6 inches up depending on the ground. The vectors that are being shown are not the normalized vectors. Another way to think about...
The swing speed of the coil is not so much a function of the frequency of the machine, but more of the filter design used in the instrument for signal processing. With the older instruments it was...
The setting for the Rx is determined by the type of ground it is by and how much trash and iron is in the ground and how strong the ground is. The Rx gain being to high can create problems with nails...
By highlighting the Ground Tracking box on the Live Control Bar and then pressing the zoom key to bring up the ground probe screen. Raise the coil in the air (but must be free of EMI) Highlight zero...
When using a single frequency on the machine best data and correlate is not a option as these two feature are only available when using the 3 frequencies modes. As the only response the machine will...
Personally I don't use the ground tracking on the V3 or V3i. I just reground balance when needed and this is very site dependent esp with the places I as some of them have fill dirt in them. I don't...
Nice find. That is the condition of those Indians here or I should say a good number of them..
rcsnake
This would be for all targets irregardless of being a higher conductive target or lower conductor. If the new target/signal goes above the signal threshold of the older target/signal, then the new...
On the subject of correlate vs. best data the depth should be the same.
However, today it seemed that the correlate sounded better on targets as opposed to the best data unless the VDI was jumping...
Hi Magic
That program looks pretty good and have a few question for ya if you don't mind.
1. Have you tried to accept +95 and set it to a low or different tone?
2. Have you tried this...
Only at times, lol
Back to the thread what I usually do is start on with my basic program that I use and adjust offset for emi if required and then lower the Rx gain if further adjustment is...
Hmmm maybe the dime is part is left out but what about the rest of the ceremony. rofl rofl rofl rofl rofl rofl rofl
rcsnake
Pulling the battery out while the detector is on will do the obvious and turn the detector off. However, changes made to a program that has not been saved through the expert menu or by turning the...
If the emi (external noise) is not to bad using the 5Hz bandpass filter will help out on cutting down on some of the noise as this has worked for me in a few places. The High pass filters will allow...
I have been detecting for 24 1/2 years and all I find is pulltabs and bottlecaps.
rcsnake
Loops can be different just by how tight the windings of each individual coil are and the shape of the coil (cross section view) from the winding of the coil.
Then the construction of the loop has...
Thought I would join this forum, since I just learned of the forum. Been metal detecting for almost 25 years and yes as some of you know I do work at Whites. Hopefully you won't hold that against me...